×

74HC193-Q100; 74HCT193-Q100

Presettable synchronous 4-bit binary up/down counter

The 74HC193-Q100; 74HCT193-Q100 is a 4-bit synchronous binary up/down counter. Separate up/down clocks, CPU and CPD respectively, simplify operation. The outputs change state synchronously with the LOW-to-HIGH transition of either clock input. If the CPU clock is pulsed while CPD is held HIGH, the device counts up. If the CPD clock is pulsed while CPU is held HIGH, the device counts down. Only one clock input can be held HIGH at any time to guarantee predictable behavior. The device can be cleared at any time by the asynchronous master reset input (MR). It may also be loaded in parallel by activating the asynchronous parallel load input (PL). The terminal count up (TCU) and terminal count down (TCD) outputs are normally HIGH. When the circuit has reached the maximum count state of 15, the next HIGH-to-LOW transition of CPU causes TCU to go LOW. TCU remains LOW until CPU goes HIGH again, duplicating the count up clock. Likewise, the TCD output goes LOW when the circuit is in the zero state and the CPD goes LOW. The terminal count outputs duplicate the clock waveforms and can be used as the clock input signals to the next higher-order circuit in a multistage counter. Multistage counters are not fully synchronous, since there is a slight delay time difference added for each stage that is added. The counter may be preset by the asynchronous parallel load capability of the circuit. Information on the parallel data inputs (D0 to D3), is loaded into the counter. This information appears on the outputs (Q0 to Q3) regardless of the conditions of the clock inputs when the parallel load (PL) input is LOW. A HIGH level on the master reset (MR) input disables the parallel load gates. It overrides both clock inputs and sets all outputs (Q0 to Q3) LOW. If one of the clock inputs is LOW during and after a reset or load operation, the next LOW-to-HIGH transition of that clock is interpreted as a legitimate signal and it is counted. Inputs include clamp diodes that enable the use of current limiting resistors to interface inputs to voltages in excess of VCC.

This product has been qualified to the Automotive Electronics Council (AEC) standard Q100 (Grade 1) and is suitable for use in automotive applications.

特性

  • Automotive product qualification in accordance with AEC-Q100 (Grade 1)

    • Specified from -40 °C to +85 °C and from -40 °C to +125 °C

  • Wide supply voltage range from 2.0 to 6.0 V

  • CMOS low power dissipation

  • High noise immunity

  • Latch-up performance exceeds 100 mA per JESD 78 Class II Level B

  • Input levels:

    • For 74HC193-Q100: CMOS level

    • For 74HCT193-Q100: TTL level

  • Synchronous reversible 4-bit binary counting

  • Asynchronous parallel load

  • Asynchronous reset

  • Expandable without external logic

  • Complies with JEDEC standards:

    • JESD8C (2.7 V to 3.6 V)

    • JESD7A (2.0 V to 6.0 V)

  • ESD protection:

    • HBM: ANSI/ESDA/JEDEC JS-001 class 2 exceeds 2000 V

    • CDM: ANSI/ESDA/JEDEC JS-002 class C3 exceeds 1000 V

参数类型

Type numberProduct statusVCC (V)Output drive capability (mA)Logic switching levelstpd (ns)fmax (MHz)Power dissipation considerationsTamb (°C)Rth(j-a) (K/W)Ψth(j-top) (K/W)Rth(j-c) (K/W)Package name
74HC193D-Q100Production2.0 - 6.0± 5.2CMOS2041low-40~125661.023SO16
74HC193PW-Q100Production2.0 - 6.0± 5.2CMOS2041low-40~1251011.027TSSOP16
74HCT193D-Q100Production4.5 - 5.5± 4TTL2043low-40~125661.023SO16
74HCT193PW-Q100Production4.5 - 5.5± 4TTL2043low-40~1251011.027TSSOP16

封装

型号封装尺寸版本回流焊/波峰焊包装状态标示可订购的器件编号,(订购码(12NC))
74HC193D-Q100
SO16
(SOT109-1)
SOT109-1SO-SOJ-REFLOW
SO-SOJ-WAVE
SOT109-1_118Active74HC193D74HC193D-Q100J
( 9353 004 45118 )
74HC193PW-Q100
TSSOP16
(SOT403-1)
SOT403-1SSOP-TSSOP-VSO-WAVE
SOT403-1_118ActiveHC19374HC193PW-Q100J
( 9353 004 46118 )
74HCT193D-Q100
SO16
(SOT109-1)
SOT109-1SO-SOJ-REFLOW
SO-SOJ-WAVE
SOT109-1_118Active74HCT193D74HCT193D-Q100J
( 9353 004 51118 )
74HCT193PW-Q100
TSSOP16
(SOT403-1)
SOT403-1SSOP-TSSOP-VSO-WAVE
SOT403-1_118ActiveHCT19374HCT193PW-Q100J
( 9353 004 52118 )

环境信息

型号可订购的器件编号化学成分RoHSRHF指示符无铅转换日期
74HC193D-Q10074HC193D-Q100J74HC193D-Q100Always Pb-free
74HC193PW-Q10074HC193PW-Q100J74HC193PW-Q100Always Pb-free
74HCT193D-Q10074HCT193D-Q100J74HCT193D-Q100Always Pb-free
74HCT193PW-Q10074HCT193PW-Q100J74HCT193PW-Q100Always Pb-free
品质及可靠性免责声明

文档 (12)

文件名称标题类型日期
74HC_HCT193_Q100Presettable synchronous 4-bit binary up/down counterData sheet2024-03-14
AN11044Pin FMEA 74HC/74HCT familyApplication note2019-01-09
hc19374HC193 IBIS modelIBIS model2019-01-31
hct19374HCT193 IBIS modelIBIS model2022-10-11
Nexperia_Selection_guide_2023Nexperia Selection Guide 2023Selection guide2023-05-10
HCT_USER_GUIDEHC/T User GuideUser manual1997-10-31
SO-SOJ-WAVEFootprint for wave solderingWave soldering2009-10-08
SO-SOJ-REFLOWFootprint for reflow solderingReflow soldering2009-10-08
WAVE_BG-BD-1Wave soldering profileWave soldering2021-09-08
SOT109-1plastic, small outline package; 16 leads; 1.27 mm pitch; 9.9 mm x 3.9 mm x 1.75 mm bodyPackage information2023-11-07
SOT403-1plastic, thin shrink small outline package; 16 leads; 5 mm x 4.4 mm x 1.2 mm bodyPackage information2023-11-08
SSOP-TSSOP-VSO-WAVEFootprint for wave solderingWave soldering2009-10-08

支持

如果您需要设计/技术支持,请告知我们并填写 应答表, 我们会尽快回复您。

模型

文件名称标题类型日期
hc19374HC193 IBIS modelIBIS model2019-01-31
hct19374HCT193 IBIS modelIBIS model2022-10-11

样品

安世半导体客户可通过我们的销售机构或直接通过在线样品商店订购样品: https://extranet.nexperia.com.

样品订单通常需要2-4天寄送时间。

如果您尚未取得安世半导体的直接采购帐号,我们的全球与区域经销网络可以协助您取得样品。