×

74HC193PW-Q100

Presettable synchronous 4-bit binary up/down counter

The 74HC193-Q100; 74HCT193-Q100 is a 4-bit synchronous binary up/down counter. Separate up/down clocks, CPU and CPD respectively, simplify operation. The outputs change state synchronously with the LOW-to-HIGH transition of either clock input. If the CPU clock is pulsed while CPD is held HIGH, the device counts up. If the CPD clock is pulsed while CPU is held HIGH, the device counts down. Only one clock input can be held HIGH at any time to guarantee predictable behavior. The device can be cleared at any time by the asynchronous master reset input (MR). It may also be loaded in parallel by activating the asynchronous parallel load input (PL). The terminal count up (TCU) and terminal count down (TCD) outputs are normally HIGH. When the circuit has reached the maximum count state of 15, the next HIGH-to-LOW transition of CPU causes TCU to go LOW. TCU remains LOW until CPU goes HIGH again, duplicating the count up clock. Likewise, the TCD output goes LOW when the circuit is in the zero state and the CPD goes LOW. The terminal count outputs duplicate the clock waveforms and can be used as the clock input signals to the next higher-order circuit in a multistage counter. Multistage counters are not fully synchronous, since there is a slight delay time difference added for each stage that is added. The counter may be preset by the asynchronous parallel load capability of the circuit. Information on the parallel data inputs (D0 to D3), is loaded into the counter. This information appears on the outputs (Q0 to Q3) regardless of the conditions of the clock inputs when the parallel load (PL) input is LOW. A HIGH level on the master reset (MR) input disables the parallel load gates. It overrides both clock inputs and sets all outputs (Q0 to Q3) LOW. If one of the clock inputs is LOW during and after a reset or load operation, the next LOW-to-HIGH transition of that clock is interpreted as a legitimate signal and it is counted. Inputs include clamp diodes that enable the use of current limiting resistors to interface inputs to voltages in excess of VCC.

This product has been qualified to the Automotive Electronics Council (AEC) standard Q100 (Grade 1) and is suitable for use in automotive applications.

Features and benefits

  • Automotive product qualification in accordance with AEC-Q100 (Grade 1)

    • Specified from -40 °C to +85 °C and from -40 °C to +125 °C

  • Wide supply voltage range from 2.0 to 6.0 V

  • CMOS low power dissipation

  • High noise immunity

  • Latch-up performance exceeds 100 mA per JESD 78 Class II Level B

  • Input levels:

    • For 74HC193-Q100: CMOS level

    • For 74HCT193-Q100: TTL level

  • Synchronous reversible 4-bit binary counting

  • Asynchronous parallel load

  • Asynchronous reset

  • Expandable without external logic

  • Complies with JEDEC standards:

    • JESD8C (2.7 V to 3.6 V)

    • JESD7A (2.0 V to 6.0 V)

  • ESD protection:

    • HBM: ANSI/ESDA/JEDEC JS-001 class 2 exceeds 2000 V

    • CDM: ANSI/ESDA/JEDEC JS-002 class C3 exceeds 1000 V

参数类型

型号 Product status VCC (V) Output drive capability (mA) Logic switching levels tpd (ns) fmax (MHz) Power dissipation considerations Tamb (°C) Rth(j-a) (K/W) Ψth(j-top) (K/W) Rth(j-c) (K/W) Package name
74HC193PW-Q100 Production 2.0 - 6.0 ± 5.2 CMOS 20 41 low -40~125 101 1.0 27 TSSOP16

PCB Symbol, Footprint and 3D Model

Model Name 描述

封装

型号 可订购的器件编号,(订购码(12NC)) 状态 标示 封装 外形图 回流焊/波峰焊 包装
74HC193PW-Q100 74HC193PW-Q100J
(935300446118)
Active HC193 SOT403-1
TSSOP16
(SOT403-1)
SOT403-1 SSOP-TSSOP-VSO-WAVE
SOT403-1_118

环境信息

型号 可订购的器件编号 化学成分 RoHS RHF指示符
74HC193PW-Q100 74HC193PW-Q100J 74HC193PW-Q100 rohs rhf rhf
品质及可靠性免责声明

文档 (11)

文件名称 标题 类型 日期
74HC_HCT193_Q100 Presettable synchronous 4-bit binary up/down counter Data sheet 2024-03-14
AN11044 Pin FMEA 74HC/74HCT family Application note 2019-01-09
SOT403-1 3D model for products with SOT403-1 package Design support 2020-01-22
hc193 74HC193 IBIS model IBIS model 2019-01-31
Nexperia_package_poster Nexperia package poster Leaflet 2020-05-15
TSSOP16_SOT403-1_mk plastic, thin shrink small outline package; 16 leads; 0.65 mm pitch; 5 mm x 4.4 mm x 1.1 mm body Marcom graphics 2017-01-28
SOT403-1 plastic, thin shrink small outline package; 16 leads; 5 mm x 4.4 mm x 1.2 mm body Package information 2023-11-08
SOT403-1_118 TSSOP16; Reel pack for SMD, 13"; Q1/T1 product orientation Packing information 2020-04-21
74HC193PW-Q100_Nexperia_Product_Reliability 74HC193PW-Q100 Nexperia Product Reliability Quality document 2023-05-29
HCT_USER_GUIDE HC/T User Guide User manual 1997-10-31
SSOP-TSSOP-VSO-WAVE Footprint for wave soldering Wave soldering 2009-10-08

支持

如果您需要设计/技术支持,请告知我们并填写 应答表 我们会尽快回复您。

模型

文件名称 标题 类型 日期
hc193 74HC193 IBIS model IBIS model 2019-01-31
SOT403-1 3D model for products with SOT403-1 package Design support 2020-01-22

PCB Symbol, Footprint and 3D Model

Model Name 描述

订购、定价与供货

型号 Orderable part number Ordering code (12NC) 状态 包装 Packing Quantity 在线购买
74HC193PW-Q100 74HC193PW-Q100J 935300446118 Active SOT403-1_118 2,500 订单产品

样品

安世半导体客户可通过我们的销售机构或直接通过在线样品商店订购样品: https://extranet.nexperia.com.

样品订单通常需要2-4天寄送时间。

如果您尚未取得安世半导体的直接采购帐号,我们的全球与区域经销网络可以协助您取得样品。

How does it work?

The interactive datasheets are based on the Nexperia MOSFET precision electrothermal models. With our interactive datasheets you can simply specify your own conditions interactively. Start by changing the values of the conditions. You can do this by using the sliders in the condition fields. By dragging the sliders you will see how the MOSFET will perform at the new conditions set.

可订购部件

型号 可订购的器件编号 订购代码(12NC) 封装 从经销商处购买
74HC193PW-Q100 74HC193PW-Q100J 935300446118 SOT403-1 订单产品